Auction Date: Tuesday, Feb 11th, 11am EST (Webcast)
Inspection: Monday, Feb 10th, 8am-4pm
Checkout Dates: 2/12 - 2/21, 8am - 4pm
Location: Monroe, LA

Featuring:

• 4 AVAILABLE - 2" x .134" Dahlstrom Stainless Tube Mill Lines, Equipped With: Tube Diameter:  .625" - 2”, Wall Thickness:  .020”- .134”, Speed:  90 - 165 inches/Min, 12” x 2500# Cooper Weymouth Double End Uncoiler, 8” - 20” Coil ID, 48” OD, Electric Brake, Forming Mill: Model:  500-10-08, Shaft Size:  2.5”, Entry Brush De-Burr Unit, 2 Sets Of Edge Guides, 5 Forming Stands, 3 Finn Pass Stands, 7 Side Idler Rolls, 2 Roll Weld Box, Mill Maxstar 700 Tig Welder, Cyclomatic Model 90A Arc Controller, Water Cooler, Hammer Roll Bead Roller, 3 Sizing Stands, 3 Side Idler Rolls, Turks Head, Flying Abrasive Saw Cut-Off, Run Out Dump Table, Single Motor Mill, Siemens Simatic HMI Digital Controller, Yaskawa Digital Drive, Siemens Simatic S7-1200 PLC, 150 KW Ajax Tocco Power Supply, Model Pacer S10
• Sunbeam Roller Hearth Bright Annealing Furnace: Max Operating Temperature 2200F, Furnace Width: 48”, Furnace Length: 30’, Cooling Length: 60’, Capacity: 5000 Lbs/hr Tubing, 3 Zones, Hydrogen, Nitrogen, Argon Gases, Atmosphere Engineering Flow Controller, Hydrogen/Nitrogen Atmosphere Controlled, Cooling Zone with Water Cooled Trays, Seco Warwick Digital Controls, Digital Atmosphere Control Panel, Entry & Exit Conveyors
• 1.125 Etna Swedger: 1.250” - .280” Diameter, Clamping Device, Hydraulic Unit, Tooling
• 1 3/4" Mackintosh Hemphill Tube Straightener: Serial No. 922, Tube Diameter: 1.750” - .313”, 6 Roll Design, Entry & Exit Tables, Manual Roll Adjustment with Readouts, 2 Motor Drive
• Ingersoll Rand Air Dryer: Model TMS 0780, Max Air Pressure: 232 Bar 16, Min & Max Amb Temp: 32/ 115 F, Max Inlet Air Temp: 131 F, Design Press:  14.5 PSI (1 bar) to 146 PSI (17 bar)
• Gardner Denver Air Compressor: Model 2449-436, 150 HP, MAWP: 150 PSI @ 250F, MDMT: -20F @ 150 PSI
• Ingersol Rand Air Compressor: Model: SSR-EP150, Capacity: 670 CFM, Rated Operating Pressure: 125 PSIG, Max Discharge Pressure: 128 PSIG, Drive Motor: 150 HP
• 300 Ton Evapco Cooling Tower (NEW): Model: USS-112-4M14, Belt No. 6B148, 2 Armstrong Pumps, Model: 4300-8x8x15-4p-100hp, Flow: 1500 USgpm, 100 HP Motor, Max Pressure: 175 PSI, 1500 gpm pump
• #3 Sink Bench/Draw Bench: Diameter Range: 2 3/8- 3/8”, Tube Length: 120’, Wall Thickness: .020” -.191”, Draw Force: 39,345#, Draw Chain Speed: 209 Feet/Min, Single Chain, Single Die Block, 250 HP Motor, 3 Snubbers, Entry & Exit Conveyors, Tooling
• #3 Draw Bench Cell: Diameter Range: 2 3/8"- 3/8”, Tube Length: 120’, Wall Thickness: .020” -.191”, Draw Force: 48,802#, Draw Chain Speed: 169 Feet/Min, Single Chain, Single Die Block, 250 HP Motor, Entry & Exit Conveyors, Ultrasonic Bar Washer (2021), Wash & Rinse Tanks, Bar Loader Conveyor, Tube Conveyor, Reeler to Remove Inner Mandrel Bars, Tooling
• #2 Sink Bench: Diameter Range: 2 3/8"- 3/8”, Tube Length: 120’, Wall Thickness: .020” -.191”, Draw Force: 39,345#, Draw Chain Speed: 209 Feet/Min, Single Chain, Single Die Block, 250 HP Motor, 3 Snubbers, Siemens Panelview 550 Digital Controller, Ultrasonic Tube Wash, Siemens Simatic HMI, Entry & Exit Conveyors, Tooling
• #2 Draw Bench Cell: Diameter Range: 2 3/8- 3/8”, Tube Length: 120’, Wall Thickness: .020” -.191”, Draw Force: 48,802#, Draw Chain Speed: 169 Feet/Min, Single Chain, Single Die Block, 250 HP Motor, Bar Wash, Bar Feed Conveyor, Bar Wash, Siemens Simatic HMI Digital Controller, Reeler to remove inner mandrel bars from Tubes, Tube Conveyor, Entry & Exit Conveyors, Tooling
• Savage Abrasive Tube Cutting Saw: Capacity: 24" Wide Layer of Tubes, Inlet & Outlet Conveyor, Back Stop, Dust Collector, Spare Blades, Top & Bottom Clamps
• Satec Systems Tensile Tester: U.T.M Model Vertex 60HVL, Serial No. 1600 with Instron System ID 60HVL C1600 & Monitor & Printer
• Large Amount Of Tooling, MRO, Racking, Welders, Toolroom Equipment & Much More…